Print This Page
14 amps delivers power when you need it, no air compressor needed. Non-slip cushioned grip, ergonomic design, high impact plastic, 10' cord. Solid state circuitry, 2 safety locks, trigger and surface. Hardened carbon steel working parts. Jam-proof nail delivery system, with angled channel to get in tight corners. Includes non-marring surface bumper. Uses 4 sizes of BN1800 series brad nails up to 1- 1/4" long.
PRODUCT FEATURES
- HEAVY-DUTY ELECTRIC
- Boxed
PRODUCT SPECIFICATIONS - Width(in): 14.5
- Height(in): 11
- Length(in): 19.5
- Weight(lb): 6.17
- Estimated Cubic Size (cu in): 518.38
Comments about Arrow Fastener Co. 1-1/4IN Brad Nailer - ET200:
Ditto to all of the above. I bought one at HD, plugged it in: nothing. I read the minimalistic directions and tried again. Nothing. I took it all apart. Nothing. I then realized, hmm....this item had been previously purchased and returned by another customer (had half a clip of brads in it "new from the box" and was missing the plastic nose gaurd.
Took it back. Got another one.
Worked fine putting small (1/2 thick" trim around interior of window frame. Then I had the audacity to try it on crown molding. I got 6 brads in (well, sort of in -- most were proud) before it died.
Please Arrow, don't have such high disregard for those few people who actually still (used to) buy your products.
Comments about Arrow Fastener Co. 1-1/4IN Brad Nailer - ET200:
I bought this because I wanted an inexpensive power nailer for odd jobs around the house and an occasional woodworking project. I don't find it easy to hold two pieces of wood and a nail in one hand and hammer on it without bending the nail, marring the wood or crunching my thumb. True, it doesn't sink the nails but, as far as I'm concerned, it does the hard part which is driving a small nail straight and true. The easy part is sinking the nail into or flush with the work. I can sink the nails easily into pine by placing my free hand firmly on the top of the nailer. It may cause some slight marring so the choice is yours.
I haven't had the nailer long enough to comment on its longevity but it works well and seems to be fairly well made.
from Boston, MA on 2/28/2007
Comments about Arrow Fastener Co. 1-1/4IN Brad Nailer - ET200:
Used gun about 4 times in one session. The gun jammed and I am unable to fix it. I am asking a freind who is a contractor to try and fix the gun for me.
Comments about Arrow Fastener Co. 1-1/4IN Brad Nailer - ET200:
3-5 shots, smoke and thats it - done. Similar to other recent reviews.
Comments about Arrow Fastener Co. 1-1/4IN Brad Nailer - ET200:
It failed after four clicks of the trigger. The guard fell off after two clicks!
Comments about Arrow Fastener Co. 1-1/4IN Brad Nailer - ET200:
Mine actually made it through 3 brads before burning up. Pathetic...
from Auburn, New York on 1/18/2007
Comments about Arrow Fastener Co. 1-1/4IN Brad Nailer - ET200:
brought nailer home, read all instructions carefully, loaded brads, plugged in outlet, on second brad gun blew up, it started smoking and that was the end of it...I returned it and brought home another, on the first brad it blew up again...not well made and very dangerous...luckyly I wasn't electricuted but someone could seriously get hurt...would not recommend this product to my worst enemy
[0 of 1 customers found this review helpful]
Comments about Arrow Fastener Co. 1-1/4IN Brad Nailer - ET200:
I bought this brad nailer for thin bead board paneling and trim work. I paid over $[...] for it,used it lightly, kept it in the box,and took very good care of it.From the start I had to finish driving the brads in the paneling and half the time no brads would even come out. It completely stopped working before I used up half of the 1500 count box of brads I bought with it. I used it very little.It still looks brand new.
I would not buy another one.